Hidromek Motor Grader HMK 380MG Operation Maintenance Manual R38002401 EN

Description

Contents:
WARRANTY CONDITIONS
1. INTRODUCTION
1.1. GENERAL INFORMATION
1.2. BEFORE STARTING OPERATION AND MAINTENANCE
1.3. INTENDED USE OF MACHINE
1.4. DIRECTIONS OF MACHINE
1.5. SAFETY INFORMATION
1.6. “CORRECT” AND “WRONG” MARKINGS IN SOME FIGURES
1.7. COPYRIGHT
1.8. DRIVING LICENSE
1.9. SPARE PARTS ORDERING PROCEDURE
1.10. LOCATION OF MACHINE AND ENGINE ID PLATES
1.11. TABLE TO ENTER SERIAL NO. AND DISTRIBUTOR INFORMATION
2. SAFETY
2.1. LOCATIONS OF WARNING LABELS AND DECALS
2.2. CONTENTS OF WARNING LABELS AND DECALS
2.3. GENERAL PRECAUTIONS
2.4. PRECAUTIONS BEFORE OPERATION
2.5. PRECAUTIONS DURING OPERATION
2.6. PRECAUTIONS DURING ROAD CONSTRUCTION
2.7. PRECAUTIONS AFTER OPERATION
2.8. PRECAUTIONS DURING SERVICE AND MAINTENANCE
2.9. GETTING ON OR OFF MACHINE
3. KNOW YOUR MOTOR GRADER
3.1. MAIN COMPONENTS AND PARTS
3.2. OPERATOR’S CAB
3.3. INSTRUMENT PANEL
3.4. CONTROL PANELS
3.5. STEERING COLUMN
3.6. CONTROL LEVERS
3.7. OPERATOR’S SEAT
3.8. SEAT BELT
3.9. ARTICULATION LOCK PIN
3.10. EMERGENCY EXIT
3.11. WINDOW WASHER FILLER CAP
3.12. STORAGE COMPARTMENT
3.13. SIDE WINDOWS
3.14. DOOR
3.15. DOOR FIXING MECHANISM
3.16. BATTERY DISCONNECT SWITCH
4. OPERATION
4.1. NEW MACHINE BREAK-IN
4.2. PRE-START INSPECTION
4.3. BEFORE STARTING ENGINE
4.4. COLD WEATHER START
4.5. CHECKING EMERGENCY STEERING SYSTEM
4.6. STARTING ENGINE
4.7. AFTER STARTING ENGINE
4.8. BEFORE MOVING THE MACHINE
4.9. MOVING THE MACHINE
4.10. CHANGING SPEED
4.11. OPERATING ON SLOPES
4.12. OPERATING ON ROUGH TERRAIN
4.13. OPERATING ON SNOW AND ICE
4.14. STOPPING THE ENGINE
4.15. AFTER STOPPING ENGINE
4.16. STOPPING MACHINE
4.17. PARKING MACHINE
4.18. PRECAUTIONS FOR USING ATTACHMENT CONTROLS
4.19. OPERATING ADJUSTMENTS
4.20. SCARIFIER DIGGING ANGLE (if equipped)
4.21. SCARIFIER PENETRATION (if equipped)
4.22. RIPPERS AND TEETH OF REAR MOUNTED RIPPER ATTACHMENT (if equipped)
4.23. RIPPER INSTALLATION FACING UPWARDS (if equipped)
4.24. RIPPER TOOTH POSITION (if equipped)
4.25. CENTERSHIFT BRACKET
4.26. HIGH BANK CUTTING – LEFT SIDE
4.27. PREPARATION FOR ROAD CONSTRUCTION
4.28. TOWING THE MACHINE
4.29. TRANSPORTATION
4.30. LIFTING THE MACHINE BY CRANE
4.31. SPECIAL SITUATIONS
4.32. LONG TERM STORAGE OF MACHINE
4.33. INSTRUCTIONS ON WITHDRAWAL FROM USE AND UTILIZATION
4.34. OPERATION AND MAINTENANCE OF AIR CONDITIONER
4.35. OPERATING TECHNIQUES (MANEUVERING)
5. MAINTENANCE
5.1. GENERAL INSTRUCTIONS
5.2. PERIODICAL REPLACEMENT OF SAFETY- RELATED PARTS
5.3. PERIODIC INSPECTION OF SERVICE BRAKES
5.4. STANDARD TIGHTENING TORQUES FOR BOLTS AND NUTS
5.5. OIL, FUEL, COOLANT
5.6. PERIODICAL INSPECTION AND MAINTENANCE LIST
5.7. CHECKS BEFORE STARTING
5.8. EVERY 10 HOURS OR DAILY MAINTENANCE
5.9. EVERY 50 HOURS (WEEKLY) MAINTENANCE
5.10. FIRST 100 HOURS MAINTENANCE
5.11. EVERY 250 HOURS (OR MONTHLY) MAINTENANCE
5.12. EVERY 500 HOURS (3 MONTHS) MAINTENANCE
5.13. EVERY 1000 HOURS (6 MONTHS) MAINTENANCE
5.14. EVERY 2000 HOURS (ANNUAL) MAINTENANCE
5.15. WHEN REQUIRED
6. TROUBLESHOOTING
6.1. ENGINE
6.2. CHASSIS
6.3. ATTACHMENTS
7. TECHNICAL SPECIFICATIONS
8. CONTACT INFORMATION
8.1. PLANT AND AFTER SALES SERVICES
9. ALPHABETICAL INDEX