Tigercat Feller Buncher 720H 724H 726H Operator Manual 73990AENG

Description

Contents:
Introduction
Available Literature
Warranty Certificates
Program Information
Introduction
Machine Identification and Serial Numbers
Machine Identification
Engine Identification
Serial Number Locations
Engine Identification
Serial Number Plate
Machine Operator Protective Structures
Modifications and Repairs
This Operator Enclosure Meets the Following Standards:
Regulatory Information
Federal Communications Commission (FCC) Notifications to User
Industry Canada (IC) Notifications to User
Vibration and Noise Levels
US Environmental Protection Agency (EPA) Warranty Certificate
Coverage
Component Coverage
Emissions Warranty Does Not Cover:
Non-Approved Field Product Changes
Section 1–Safety
Safety Alert Symbol
Signal Words
General Safety Precautions
Hazard Zone
Personal Protective Equipment (PPE)
Prepare for an Emergency
Keep Guards and Protective Devices in Place
Keep Clear of Moving Parts
Prevent Exhaust Build-Up
Climbing On and Off the Machine
Hazardous Materials
Fluid Injection Injury
Fire Prevention
Operating Safety Precautions
Emergency Exits
Battery Disconnect Switch
Safety Interlocks
Preparing the Machine for Use
Keep the Operator’s Station Clean
Use and Maintain the Seat Belt
Precautions for Starting the Engine
Precautions for Stopping the Engine
Parking the Machine
Release Pilot System Pressure
Operating the Machine Safely
Operate Only for Intended Use
High Voltage Contact
Avoiding Injury from Backover Accidents
Visibility
Minimizing Vibration During Use
Machine Stability and Traction
Tires
Attachment Safety Precautions
Preparing the Attachment for Use
Operating the Attachment
Using High-Speed Disc Saws Safely
Servicing Safety Precautions
Preparing the Machine for Maintenance
Releasing Hydraulic Pressure
Safety Devices
Engine Lockout/Tag Out
Performing Maintenance
Performing Maintenance With the Engine Running
Welding Safety
Transporting Safety Precautions
Storage Safety Precautions
Label Locations
Safety Labels
Operator’s Manual Location
Read the Operator’s Manual
Use the Seat Belt
Remove the Ignition Key Before Servicing the Machine
No Riders
Emergency Exit
Emergency Exit, Hand Tighten Only
Exposure to Diesel Engine Exhaust
Keep Back
Crush Hazard–Centre Joint
Crush Hazard–Boom
Entanglement Hazard From Rotating Parts
Cutting Hazard From Rotating Fan Blade
Explosive Release of Hot Cooling System Pressurized Fluid
Explosion Hazard From Ether
Stored Energy Hazard (Accumulator)
Fire Prevention
Fire Extinguisher Access Hole
Notice Labels
Engine Idle (Tier 4f)
Engine Coolant Shut-Off Valves (if Equipped with Engine Coolant Heater)
Do Not Tow
Engine Coolant
Information Labels
Tie-Down/Lift Instruction Label
Tie-Down Points
Lift Points
Retrieval/Tow Points
Section 2–Controls and Operation
Pictogram Descriptions
Joystick Controls
Joystick Functions–Home Screen
Joystick–Left
Joystick–Right
Function Mapping
Saw/Shear Functions
Accumulation Mode
Foot Pedal Controls
Left Foot Controls
Brake Foot Pedal
Right Foot Controls
Quick-Attach Boom Adapter (Optional)
Installing Attachment
Removing Attachment
Cab Control Panels
Front
Right Console
Right Armrest
Left Armrest
Rear Wall
Lower Front
Upper Right
Upper Left
Fire Extinguisher
Cameras and Video Displays (RearVIEW Camera System)
Monitor
Cameras
Pressurized Water System
Air Vents–Cab
Filters–Cab
Recirculating Air
Fresh Air
Blind, Tinted, Skylight
Rear View Mirrors
Blind, Tinted, Front Window
Operator’s Manual Case
First Aid Kit
Battery Disconnect Switch
Batteries
Engine Coolant Shut-Off Valve
Fire Detection System
Introduction
System Operation
System Components
System Test
Avoiding Damage and False Signals During Machine Service
System–Overview
Emergency Exits
Cab Doors
Side Window Guards
Side Windows
Escape Hatch (Skylight)
Operator’s Seat
Adjusting the Operator’s Seat
Seat Climate Control
Adjusting the Armrests and Control Pods
Seat Belt
Computer Control System
Home Screen
Hydraulic Oil Return Filter Bypass *
Level Gauge Symbol **
Temperature Gauge Symbol ***
Additional Gauges Screen
Engine Page
Adjust Page
Information Page
Operator
Expansion Menu
Computer Menus
Main Menu
Menu Navigation
System Menu
Measure Menu
Adjust Menu
Preferences Menu
Computer Messages
Critical Messages
Error Messages
Alert Messages
Information Messages
IQANgo
Summary of App Operations
Connect To The Machine
Disconnect From The Machine
Log In
Get Clone
Get Settings
Get Log
Forward Data
Receive Data
Send To Machine
System Menu
Logs Menu
Measure Menu
Adjust Menu
Remote Assistance Mode
Battery Boosting
Battery Booster Cable With Clamps
Operating the Machine
Pre-Start Checks
Starting Engine
Parking Brake Test
Cold Weather Starting
Restarting an Engine That Has Run Out of Fuel
Stopping Engine
Hot Engine Shutdown Prevention Strategy
Tier 4F Machines
Tier 2/Non-Certified Machines
Temperate Engine Shutdown
Hot Engine Shutdown
Section 3–Lubrication and Maintenance
New Machine Maintenance
Initial Pre-Delivery Inspection
Wheels
First 125 Hour Inspection Report
Tightening Points
Tigercat Fluid Analysis Program
Tigercat Fluid Analysis Kits
Sampling Schedule
Fluid Sample Collection Procedures
General
Check Emergency Exits Monthly
Fire Prevention
Fire Extinguisher
Scheduled Maintenance
Every 8 Hours
Every 48 Hours
Every 125 Hours
Every 250 Hours
Every 500 Hours
Every 1000 Hours
Every 1500 Hours
Every 2000 Hours
Every 2 Years or 3000 Hours
Every 3 Years
Service and Lubrication Points
Approved Hydraulic Oils
Articulation Lock Bar Installation
Lift Boom Cylinder Lock Installation
Towing Instructions
Requirements Prior to Towing
Access Doors and Covers
Rear
Rear Door Latch
Rear Door Safety Stop
Left Side
Right Side
Underside
Lower Access Panels
Inner Compartment Access Panels
Cab Access Panels
Front Valve Compartment Cover
Centre Joint
Lubrication
Maintenance And Inspection
Transmission
Checking Oil Level
Draining and Refilling
Pump Drive Gearbox
Checking Oil Level
Draining and Refilling
Parking Brake
Lubrication
Checking Oil Level
Draining and Refilling
Driveshafts
Front and Rear Shaft Slip Spline Lubrication
Middle Shaft Slip Spline Lubrication
Installation
Axles
Rear Axle–Limited Slip Additives
Checking Oil Level
Draining and Refilling
Hydraulic System
Refilling the Hydraulic System
Ultraviolet (UV) Hydraulic Oil Dye
Hydraulic Oil Tank
Hydraulic Oil Return Filter
Drive Pump Charge Pressure Filter
Case Drain Strainer
Engine Coolant Heater Unit (Optional)
Components
Engine Coolant Heater Preventative Maintenance (Webasto)
Low Voltage Disconnect Adjustment (Webasto)
Lockout Reset Procedure (Webasto)
Air Conditioning System
Components
Inspection of the A/C System
Engine Belts
Fuses and Relays
Fuse and Relay Panel–Cab
Main Fuse and Relay Panel
Battery Care
Engine Filters–Remove and Replace
Engine Oil Filter
Engine Crankcase Ventilation Filter
Fuel Filter
Fuel Filter/Water Separator
Fuel Specifications
Tier 4f Engines
Tier 2/Non-Certified Engines
Biodiesel
Fuel Additives
Refuelling Procedure
Ground Level Quick-Connect
Fill Cap
Fuel Tank
Fuel Fill Strainer
Fuel Level Sender
In-Tank Fuel Strainer
Air Intake System
Air Intake Tubing and Joints
Engine Air Precleaner
Air Cleaner
Air Filter Restriction Indicator
Air Filter Restriction Sensor
Engine Coolant
Engine Coolant Specifications
Check Engine Coolant Level
Draining Engine Coolant
Adding Engine Coolant
Aftertreatment System
Diesel Exhaust Fluid (DEF) Handling and Specifications
DEF Tank
Filling the DEF Tank
Cleaning the DEF Fill Strainer
Draining and Cleaning the DEF Tank
In-Line DEF Strainer
Checking or Replacing the In-Line DEF Strainer
DEF Supply Module
Pressurized Water System Maintenance
Operation
System Test
Pressurized Water Tank
Fill and Charge The System
Purge The System
Emergency Exit Maintenance
Right Cab Door
Escape Hatch (Skylight)
Tires
Inflation Procedure
Pressure Washing
Anti-Corrosion Spray
Road Salt or Brine
Pressure Washing Procedure
Cleaning Cooler Package
Cleaning Cab Interior Plastic
Cleaning Cameras and Video Displays
Cameras
Care of Polycarbonate Windows
Inspection and Maintenance
Fire Precautions
Resistance to Chemicals
Resistance to Hot Water
Cleaning Instructions
Concealing Hairline Scratches
Graffiti Removal
Cleaning Side Windows
Side Window Guards
Storing the Machine
Recommended Storage Conditions
Preparing the Machine for Storage
Inspection and Maintenance During Storage
Preparing the Machine for Use After Long-Term Storage
End of Service Life
Preparing the Machine for Disposal
Disposing of Fluids and Components
Torque Chart–720H/724H/726H
Torque Specifications
General Torque Specifications
Parker Assembly Torque
Eaton Aeroquip Assembly Torque
Tire Pressures
Pressure and Speed Settings–720H/724H/726H
Saw–Gear Pump
Saw–Piston Pump
Index